Schedule Now

 

 

We have found the article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the web and decided it made sense to discuss it with you on this site.

Setting up a tub isn't specifically rocket science, but it does need strong plumbing, woodworking, and often, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult project. If the old bathtub is conveniently obtainable, the task can move rapidly; if you need to open up a wall surface to get rid of the old bathtub and position the new tub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly require a helper to move out the old tub as well as set in the brand-new one. Make certain you have actually certified on your own for the work and also fit trying it. Rather than hiring a contractor to take over a halfway-completed project, it is better to think about utilizing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This article will help you install a new bathtub in your washroom if you have actually currently purchased a new bathtub and also do not need to change the setup of your previous water pipelines.
Your tools and also material checklist should consist of the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Preparing for the Installation

Firstly, the sustaining frame provided with the bathroom ought to be fitted (if required) according to the manufacturer's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to make sure that if the faucet includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to avoid strain on the tub.
Fit the flexible faucet ports to the bottom of both faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.

 

 

Removing Old Taps

If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be rather problematic because of the limited gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a towel ready for the staying water that will certainly come from the pipelines. As soon as the supply pipes have been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.

 

 

Mounting the Bath tub

Using the two wood boards under its feet, position the bathtub in the required setting. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four small points.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the bath tub until the spirit level reads level.
To set up faucets, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Turn on the water system and also examine all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill up the tub as well as additionally inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the tub needs to wait till the bath tub has actually been made use of at the very least once as this will settle it into its last placement.

 

 

Suitable New Touches

If the tails of the brand-new taps are plastic, then you will need a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end provides a link to the current supply pipelines.
If you require to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the faucet as well as the sink. Protect the tap in position with the maker offered backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former kind should be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Bath tub

In the area where the bathroom meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to split a rigid seal, creating the water to penetrate the wall surface between the bathroom and also the tiling, leading to issues with wetness and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes as well as cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to enable the motion experienced when the bathtub is in usage. The sealer can crack relatively very early if you do not take into account this movement before securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the market. It is a good idea to fit the floor tiles utilizing waterproof or waterproof adhesive as well as cement.

 

Bathtub Installation

 

How Important Is A Bathtub To Your Home?

 

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

 

Install Piping Before Tub

 

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

 

Position the Tub

 

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

 

Assemble Drain Connections

 

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

 

Place a Pipe For the Shower Head

 

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

 

Attaching Hot and Cold Water Lines

 

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

 

Install the Spout

 

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

 

Check For Leaks

 

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

 

estore the Bathroom Wall

 

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

 

I ran across that page about How to Install a Bathtub Yourself while doing a lookup on the search engines. Enjoyed reading our content? Please share it. Help another person find it. We love reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Free Estimate